Microstructures and phases analysis of the 60Al-40V master alloy produced by aluminothermic process

Get full text

Tribology in coal-fired power plants by Moumakwa, Donald Omphemetse

Get full text

Influence of grain size and niobium content on the creep resistance of ferritic stainless steels by Cain, Victoria

Get full text

Out-of-plane strength and stiffness prediction of SA pine cross-laminated timber by Jacobs, M. J.

Get full text

High Octane and Oxygenate test set-up for CFR Octane Engine. by Bergenthuin, Johannes Gysbertus

Get full text

Influence of binder and active filler content on the shear properties of high ra bitumen stabilised materials by Cotterrell, Ross Glenn

Get full text

Changes in material characteristics of AISI 430 stainless steel plates subjected to repeated blast loading by Shangase, Thobani Paul

“…Parts of the microstructures displayed equiaxed/recrystallised grains characteristic of restoration processes, owing to high temperatures. Vickers hardness tests indicated an increase in material hardness as the number of blasts was increased, with a maximum hardness in the central region of the plates. …”
Get full text

Effect of anti-corrosive coatings on the bond between corrosion-damaged rebar and concrete repair materials by Moolla, Muhammad Ameen

“…Two steel bars, Y12 and Y16, of different diameters were considered. Three repair materials with CEM I 52.5N were considered in this study, which included one concrete with a w/b ratio of 0.45 and two mortars with w/b ratios of 0.47 and 0.65, referred to as C45, M45 and M65, respectively. …”
Get full text

The preparation of low-temperature fusion enamel coatings for corrosion control using local raw materials by Danquah, Andrews

Get full text

A comparative study of insulator materials exposed to high voltage AC and DC surface discharges by Heger, Gernot

Get full text

Screening of butternut (Cucurbita moschata) cultivars for resistance to Black rot caused by Stagonosporopsis spp.

Get full text

Pilot-scale production and physicochemical properties of mycelium-based materials and diversity assessment of a fungal biobank by Rajaruthnam, Sunthuri

Get full text

Fabrication and characterization of aluminum-carbon nanotubes (Al-CNT) functionally graded cylinders by Morad, Sherry Samy

“…In the current research, an experimental study was conducted to develop a route to fabricate Al-CNT functionally graded cylinders varying materials along radial direction. Larger content of CNT reinforcement was selectively used at the outer layers to provide the highest strength, hardness and wear resistance at the surface subjected to higher stresses and more severe environments. …”
Get full text
Get full text

The unlubricated sliding wear behaviour of austempered ductile irons by Fordyce, E P

Get full text

Fabrication & Characterization of Hybrid Piezoelectric/Triboelectric Nanocomposite Nanogenerators via Fusion Deposition Modeling by El Toukhy, Khaled

“…For the walking test, the best performance was recorded to have a peak potential difference of 22 V and 23.6 V. …”
Get full text
Get full text

Feasibility study on the reinforcement of Ti6Al4V with tungsten carbide particles using selective laser melting by Mthembu, Noluthando Bright

Get full text

Mutation breeding of Cavendish bananas for resistance to Fusarium oxysporum f. sp. cubense tropical race 4 by Bothma, Sheryl

Get full text

Investigation into the surface modification of Ti-6Al-4V to facilitate antimicrobial ionic silver integration for use in implantable orthopaedic devices by Vazirgiantzikis, Iosif

“…Malignant bone tumours often require a patient to make the choice between limb salvage surgery and complete amputation. The Ti-6Al-4V alloy is the material of choice for implantable orthopaedic devices as it provides a favourable combination of biocompatibility, corrosion resistance and mechanical properties. …”
Get full text